Construction | Restoration | Renovation | Flooring | Roofing
#1 Paint Emergency: Water damage repair
For efficiency, stay “in sequence” when doing this type of repair work. Do all of the bedding at the same time, and let it dry per the mud manufacturers recommendation. The next step is the first skim. While tape is just over 2″ wide, it is often necessary to create a skim that is 16-24″ wide to perfectly blend a repair joint into its surroundings. Several sizes of mud knives come into play, with the 6″ being the smallest. It is handy to have several sizes, and a “hawk”, which is a large flat plate with handle, used to hold the mud that you are skimming with the knives. It is usually necessary to do as many as 3-4 rounds of full skimming in a repair job. It is critical to keep the skims as thin and smooth as possible, to minimize the amount of sanding that is required between coats of mud. Ideally, you are just taking the “edge” off the dried skims before applying the next. Skimming is a real art, to do it well, and it is a great skill to learn and master.
If the phone works like before after you have cleaned it, it is great. But, if it hasn’t, it is time that you bring the phone to us so that we can take a look at it. We will diagnose your device and tell you whether or not it is recoverable and offer the best solution for your problem. We shall make every effort to restore your device from the water damage. Even if we are unable to save your phone, we have the necessary skills to retrieve all important information that you might need from your device so that you can transfer it to device.
GREATER SEATTLE WATER DAMAGE REPAIR & FLOOD RESTORATION
Thank you very much for your services on our floor issue. I speak for both myself and Dale when I say we were very pleased with your company’s service. It was great that you were accessible when we needed you. I also want to commend you on your patience. You handled the challenges of insurance timelines beautifully. The work you did was great. As you know I am in the construction business and know a bit about how things should go. I never felt anything less than professionalism and high-quality work. I would highly recommend you and your company to anyone. I can’t thank you enough for your help.
Repairing Water Damage – Who to Call
Erasing signs of the damage in your bathroom is dependent on the severity of what’s occurred. You may need to bring in a long line of contractors to get things back in order. In a worst-case scenario, your bathroom might have suffered structural damage, and mold and mildew is present as well. If those are the facts, you’re going to need to call in a general contractor, as well as a mold and mildew remediation specialist, to return your bathroom and home to a safe, usable state. Other than that, assess where the damage is worst and start there. If your drywall is ruined, call in a drywall contractor and painter to get things back to normal. If your flooring is cracked or coming loose, call in a flooring contractor. You get the idea.
Need to find a pro for your water damage repair?Find Pros
After dealing with the source of the damage, combating mold and getting the area dry again, the final step is to repair the damage. Installing new drywall or plaster is something you can do yourself -- but it may be too difficult for you to apply to a ceiling if you have no experience, because the ceiling is the most difficult area to drywall or plaster. For severe damage, you may need to replace insulation behind the drywall, as well, and replace or reinforce damaged wood. For minor damage, you can cut or sand the damage out and apply drywall compound to fill in the hole or crack. Then sand it smooth and paint. If your damage was not severe enough to warrant drywall removal and there was no mold, consider merely painting the ceiling with a stain-blocking primer and a coat of paint to cover up any water stains.
How To Repair Water Damage From A Leaking Water Heater
Water heater is leaking from the bottom and is on a raised pedestal covered with drywall and plaster. The plaster on the top portion which is the portion the waterheater sits on , is moist. I’m drying it out with a fan at the moment. Do I need to replace the,whole portion or can I dry it out, then put the heater on the drain pan and begin hooking up my water heater or should I wait til completely dry? I cut some openings to get some cross ventilation under the pedestal as well.
Water Damage Restoration & Repair
The harmful effects of water are sharply reduced by prompt and effective intervention, especially within the first 24-48 hours. Even though the damage may look severe, cleanup and restoration can produce amazing results. From furniture to family heirlooms, office computers to production machinery, BELFOR has successfully restored water-damaged structures and property for more than 70 years.
All water soaked building materials, drywall, insulation etc, should be removed as soon as possible. These materials cannot be reused even once they have been dried. Fans should be placed throughout the affected area to increase air flow and dry out any wooden studs or structural elements of the home. Moisture meters can be used to determine the level of residual moisture in any material you are attempting to dry. The goal is to completely dry everything including wooden studs and sub-floor within 48 hours in order to prevent black mold growth.